Home › Guides › Laser cutting speed explained: power, thicknes…

Laser cutting speed explained: power, thickness, mm/s vs mm/min and what it costs you

A laser cutting a sheet of plywood on a honeycomb bed

Speed is the setting that decides how long your job takes and how much it costs. This guide explains what the number means, how to read it in any unit, and how to turn it into time and money.

What laser cutting speed actually means

Laser cutting speed is how fast the laser head moves along the cut path. It is a feed rate. A speed of 10 mm/s means the beam travels 10 mm along the line every second.

Most machines use three different speeds. Cut speed is the slow, careful move while the laser fires and burns through the material. Engrave speed is the faster sweep used when the head scans back and forth over a surface. Travel speed is the rapid move between cuts, with the laser off. Travel speed is high and rarely matters for quality, but it adds to your total time.

One speed number on its own tells you almost nothing. 20 mm/s is fast for a 10 W diode on plywood and very slow for a 150 W CO2 on thin paper. A speed only means something with three other facts: the laser power, the material, and its thickness. Lens, focus and air assist matter too. When someone shares "my cut speed", always ask what machine and what material it was for.

mm/s vs mm/min vs in/min

Laser software does not agree on units. This is the most common reason a copied setting goes wrong by a factor of 60.

The conversions are simple. Divide mm/min by 60 to get mm/s. For inches per minute, multiply by 25.4 and divide by 60.

mm/minmm/sin/min
6001023.6
12002047.2
300050118
6000100236
254042.3100

If you would rather not do the maths, use our laser speed converter. Check the unit label in your software before you type anything in. A speed of 600 read as mm/s instead of mm/min is 60 times too fast, and the cut will not go through.

Speed, power and thickness: the triangle

Cutting is about energy delivered per millimetre of path. That energy is roughly power divided by speed. Raise the power or slow down and each millimetre gets more energy. Lower the power or speed up and it gets less.

Thickness pushes back hard. Doubling the thickness does not halve the speed. On wood and acrylic, speed usually drops by 2 to 3 times when thickness doubles, because the beam has to burn deeper, the kerf gets narrower at the bottom, and smoke blocks the beam. That is why 6 mm plywood takes far more than twice as long as 3 mm.

Slower is not always better. As you slow down:

For thick material, two faster passes often beat one slow pass. The second pass cuts through whatever the first one missed, with less charring and a cleaner edge. The trade-off is that your part must not move between passes.

Typical cutting speeds by machine class

These are typical ranges from settings shared by owners and manufacturers' published tables. Treat them as a starting point, not a promise. Your lens, focus, air assist and the actual sheet will shift them.

MaterialMachineTypical speed
3 mm birch plywood10 W diode~4 mm/s
3 mm birch plywood20 W diode~6 mm/s
3 mm birch plywood40 W diode~8–10 mm/s
3 mm birch plywood40–55 W CO2~12–14 mm/s
3 mm birch plywood60–80 W CO2~20 mm/s
3 mm birch plywood100 W+ CO2~24 mm/s
3 mm MDF20 W diode~5 mm/s
3 mm MDF60–80 W CO2~22 mm/s
3 mm cast acrylic40–55 W CO2~10–12 mm/s
3 mm cast acrylic60–80 W CO2~18 mm/s
3 mm clear acrylicDiodeNot recommended (the beam passes through)
6 mm plywood40 W diode~3–4 mm/s, 2 passes
6 mm plywood60–80 W CO2~8 mm/s
6 mm acrylic60–80 W CO2~6 mm/s

Sheet metal is a different world. A 1–2 kW fiber laser cuts 2 mm mild steel at roughly 100–150 mm/s (6–9 m/min), and 6 mm mild steel at around 30 mm/s. Fiber machines also use assist gas, so the numbers are not comparable with wood settings.

For the full per-material chart, see our laser power and speed chart. For material pages with typical cost, see 3 mm plywood and 6 mm plywood.

How speed becomes machine time

Cutting time is simple to estimate:

time = cut length ÷ speed × passes + pierce time + travel

Pierce time is the pause while the laser burns its first hole at the start of each cut. It is about 0.2–0.5 s on wood with a diode or CO2 laser, and about 0.5–1 s on steel. A part with 200 small holes pays for 200 pierces, so it can add real minutes. Travel moves add a little more.

Here is a worked example. A job has 2.4 m of cutting in 3 mm plywood, which is 2400 mm.

Same part, same wood, five times the time. Pierces and travel come on top of both numbers.

Engraving works on area, not length. The formula is area ÷ (speed × line interval). For a 100 × 100 mm block at 300 mm/s with a 0.1 mm line interval, that is 10,000 ÷ (300 × 0.1), which is about 333 s, or 5.6 minutes. Add some time for overscan, the extra distance the head travels past each line to get up to speed.

Do your own numbers with the cutting time calculator and the engraving time calculator.

How speed drives the price

Most laser services price by machine time. The formula is machine time × hourly rate, plus material and setup. Speed sets the time, so it sets the price.

Take the same 2.4 m plywood job. A small diode service might charge about €35 per hour. A CO2 service might charge about €60 per hour.

The machine with the lower hourly rate makes the more expensive part. A faster, pricier machine often wins on cost because the clock runs for so much less time. This is also why thick material costs so much more: speed falls 2–3 times, and the time follows.

For a full breakdown, read how much laser cutting costs, or run your own job through the laser cutting cost calculator.

Finding your own speed: the test grid

Charts get you close. Your machine decides the rest. The reliable way is a test grid: a set of small squares, each cut at a different speed and power. Cut it on a scrap of the same material, then look at which squares fall out cleanly.

Change speed first, then power. Pick the fastest speed that cuts through on every square, then use the lowest power that still does it. That gives you the shortest time and the least charring. Our test grid generator builds the file, and the guide to a material test grid shows how to read the result.

Speed mistakes that cost money

FAQ

What is a good laser cutting speed for 3 mm plywood?

It depends on power. Typical settings shared by owners are about 4 mm/s for a 10 W diode, 6 mm/s for 20 W, 12–14 mm/s for a 40–55 W CO2 laser, and around 20 mm/s for 60–80 W CO2. Use these as a start, then confirm with a test grid on your own sheet.

How do I convert mm/min to mm/s for my laser?

Divide mm/min by 60. So 600 mm/min is 10 mm/s, 1200 is 20 mm/s and 3000 is 50 mm/s. For inches per minute, multiply by 25.4 and then divide by 60, so 100 in/min is about 42.3 mm/s. Always check which unit your software shows.

Does more power always mean faster laser cutting?

Mostly yes, but not without limits. More power lets you move faster for the same energy per millimetre, which is why 60–80 W CO2 cuts 3 mm plywood about five times faster than a 10 W diode. Thickness, focus, air assist and tiny geometry cap the real gain.

Why is my laser cutting slower than the chart says?

Usual causes are a dirty or wrong lens, focus set off by a millimetre or two, weak air assist, and a different batch of material than the chart used. Small parts also slow the head because it cannot reach full speed on tight curves. Run a test grid and trust that over the chart.

How does laser cutting speed affect cost?

Most services charge machine time × hourly rate. Slower speed means more minutes and a higher price. For 2.4 m of 3 mm plywood, a 10 W diode at 4 mm/s takes 10 minutes, about €5.83 at €35/h. A 60 W CO2 at 20 mm/s takes 2 minutes, about €2.00 at €60/h.

What speed should I engrave at?

Engraving runs much faster than cutting. Many CO2 owners engrave wood at roughly 200–400 mm/s and diode owners at lower speeds, with power set to give the depth they want. Engrave time is area ÷ (speed × line interval), so doubling the speed halves the time. Use a test grid to find the right power.

← All guides · Price your file · By machine