Home › Guides › LaserPecker 4 settings — power & dep…
LaserPecker 4 settings — power & depth cheat sheet

Searching for LaserPecker 4 settings, the settings PDF, or settings for glass, wood and stainless steel? LaserPecker publishes one material table for the LP4, and it does not use mm/s. It gives Power % and Depth % for each of the two lasers, 10 W 450 nm diode and 2 W 1064 nm infrared, at 1k, 2k or 4k resolution. Quick answer: basswood cuts at 100 / 98 with the diode and stainless steel fills at 100 / 91 with the infrared. Depth is LaserPecker’s speed slider: the higher the number, the slower the head. We have not run an LP4 ourselves, and the store shows every LP4 variant unavailable, which the page covers below.
Quick answer: every number below is a Power % / Depth % pair copied from LaserPecker’s own table “Material Parameter Settings for LP4” (the V655 firmware section, article updated 20 October 2026), which is also printed on laserpecker.net as a material-settings page. The vendor labels are Fill, Picture, Line Engraving and Line Cutting. LaserPecker does not publish passes, line spacing or a speed in mm/s. For laserpecker 4 settings for wood and acrylic the table has rows; for tumbler and leather it does not, and we left those out.
LaserPecker 4 settings (laser / Power % / Depth % / resolution)
Each row is copied whole from LaserPecker’s table, with the operation label it uses; “–” means LaserPecker publishes no value for that laser. The table has 192 filled rows; this is a selection of the materials people search for, 1k resolution unless stated. Nothing here is our own cut: run a material test grid on scrap first. Thickness is not published for these rows.
| Material | Job (LaserPecker label) | Resolution | 2W infrared: power / depth | 10W diode: power / depth |
|---|---|---|---|---|
| Stainless steel | Fill | 1k | 100 / 91 | 100 / 91 |
| Stainless steel | Fill | 2k | 50 / 92 | 30 / 86 |
| Stainless steel | Line Engraving | 1k | 100 / 94 | 100 / 96 |
| Aluminium oxide (anodised) | Fill | 1k | 100 / 81 | 100 / 81 |
| Aluminium oxide (anodised) | Fill | 2k | 50 / 81 | 50 / 81 |
| Aluminium oxide (anodised) | Line Engraving | 1k | 100 / 91 | 100 / 91 |
| Basswood plank | Fill | 1k | – | 10 / 86 |
| Basswood plank | Fill | 2k | – | 30 / 64 |
| Basswood plank | Line Engraving | 1k | – | 10 / 94 |
| Basswood plank | Line Cutting | 1k | – | 100 / 98 |
| Black walnut | Fill | 1k | – | 50 / 89 |
| Black walnut | Line Cutting | 1k | – | 100 / 98 |
| MDF | Line Cutting | 1k | – | 100 / 95 |
| Bamboo strip | Fill | 1k | – | 70 / 81 |
| Acrylic | Fill | 1k | 60 / 91 | 50 / 89 |
| Acrylic | Line Engraving | 1k | 60 / 96 | 50 / 95 |
| Acrylic | Line Cutting | 1k | – | 100 / 95 |
| Kraft paper | Line Cutting | 1k | – | 10 / 99 |
| Cardboard | Line Cutting | 1k | – | 60 / 97 |
| Cardstock paper | Line Cutting | 1k | – | 30 / 94 |
| Cowhide | Line Cutting | 1k | – | 30 / 35 |
| Glass | Fill | 1k | – | 100 / 86 |
| Glass | Line Engraving | 1k | – | 100 / 94 |
What Depth means: LaserPecker’s LightBurn guide maps Depth 1% to 24,000 mm/min and Depth 100% to 240 mm/min (faster to slower) and Power 1–100% to LightBurn power 130–255. Only those two end points are published, so we do not convert the rows in between. Read the table the way the vendor does: low Depth is a fast raster, Depth in the 90s is a slow vector line. Line Cutting at 100 / 98 on basswood is close to the slowest speed the machine runs, which fits a 10 W diode with a ceiling of 8 mm balsa.
Compare with the xTool F1: the F1 is the same class of machine (10 W diode plus 2 W infrared), and our F1 guide cuts 3 mm basswood at 90% and 3 mm/s in one pass: slow, at nearly full power, as LaserPecker’s 100 / 98 says too.
The charts from this site in one printable book: The Laser Settings Handbook — 18 machines, 11 material charts, the 15 fixes and a settings log in 168 pages. Machine guides added since the book was made are free online only. Read the free 13-page sample.
Get an exact price for the LaserPecker 4
Settings give the time; the price is time times your hourly rate plus material and setup. Use the laser cutting time calculator for the time, then the calculator. Because LaserPecker gives Depth and not mm/s, take the time from a test cut.
Models, specs and whether it is still sold
| Item | Value | Source |
|---|---|---|
| Lasers | 10 W 450 nm blue diode (continuous) plus 2 W 1064 nm pulsed infrared | LaserPecker LP4 buying guide, FAQ |
| Head | Galvanometer | LaserPecker LP4 effective-working-area article |
| Work area | 160 × 120 mm; 160 × 300 mm with the slide extension | LaserPecker LP4 buying guide, product page |
| Max speed | 4,000 mm/s working | LaserPecker LP4 buying guide |
| Cutting | 8 mm balsa and 5 mm dark opaque acrylic in one pass, blue laser only; the infrared marks and does not cut | LaserPecker LP4 product page, FAQ |
| Software | LaserPecker Design Space, LightBurn | LaserPecker LP4 buying guide, LightBurn article |
| Weight | 4 kg | LaserPecker LP4 buying guide |
Still sold? Unclear. On 14 November 2026 LaserPecker’s store data showed every LP4 variant as unavailable, while the product page, the navigation menu and the support site were still live. The page gives no reason, so we cannot say whether it is sold out or paused. The newer LP5 (20 W diode plus 20 W fiber) is also marked unavailable. The guide is for owners; check the store before buying.
Blanks for a LaserPecker 4
A 160 mm bed means small blanks.
Anodised aluminium business cards: Check price on Amazon ↗
Stainless steel dog tag blanks: Check price on Amazon ↗
Basswood sheets 3 mm: Check price on Amazon ↗
Slate coasters: Check price on Amazon ↗
Disclosure: some links are affiliate links — if you buy through them we may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Prices are approximate list prices at the time of writing; always check the current offer.
Bed size: what actually fits
The LaserPecker 4 has a working area of 160 × 120 mm, 160 × 300 mm with the slide extension. It is a small-items machine.
| Common stock | On this machine (160 × 300 mm with slide) |
|---|---|
| A4 sheet | Does not fit: cut it down first |
| 300 × 300 mm craft ply | Does not fit: cut it down first |
| 600 × 400 mm sheet | Does not fit: cut it down first |
What the LaserPecker 4 settings above do not cover
- No mm/s and no pass counts. LaserPecker publishes neither; add passes only after a test.
- No thickness. The rows do not say what thickness each was set for.
- No tumbler or leather rows. LaserPecker publishes Cowhide Line Cutting only; we show that one.
- Older firmware. The older V654-and-earlier table uses a different Depth scale and is left out. Use these rows with V655 or later.
- Cut with the blue laser only. The infrared marks under 0.1 mm per pass; it does not cut.
Troubleshooting: symptom, cause, fix
| Symptom | Likely cause | Fix |
|---|---|---|
| Cut does not go through | Depth too low, so the head moves too fast | Raise Depth in steps of 2–3, or run a second pass. |
| Metal mark is faint | Wrong laser or resolution | Use the infrared row for bare metal; the 1k rows are the most heavily marked. |
| Numbers look wrong on an old firmware | The V654 table uses a different Depth scale | Update to V655 or later before using this page. |
| Glass does not mark | Clear glass is transparent to the beam | Use a coating or tint; LaserPecker’s own glass row is 100 power. |
Material cost per item
A 160 mm bed suits small blanks. See where to buy laser materials.
FAQ
What are LaserPecker 4 settings for wood?
LaserPecker's V655 table lists basswood plank Fill at 10 power / 86 depth (1k) or 30 / 64 (2k), Line Engraving at 10 / 94, and Line Cutting at 100 / 98, all on the 10W diode. Black walnut Line Cutting is 100 / 98 and MDF 100 / 95. Passes and thickness are not published.
What does Depth mean on the LaserPecker 4?
Depth is LaserPecker's speed setting in percent: higher is slower. Its LightBurn article maps 1% to 24,000 mm/min and 100% to 240 mm/min, and publishes only those end points.
What are LaserPecker 4 settings for stainless steel?
For the 2W infrared laser LaserPecker lists Fill at 100 / 91 (1k) or 50 / 92 (2k), and Line Engraving at 100 / 94, as power / depth.
What are LaserPecker 4 settings for glass?
The table has a Glass row for the 10W diode: Fill at 100 power / 86 depth (1k), and Line Engraving 100 / 94. Clear glass is transparent to the beam, so expect a coating or tint to be needed.
Is there a LaserPecker 4 settings PDF?
LaserPecker publishes the same table as a PDF and as a web page on laserpecker.net, and in its Help Center article Material Parameter Settings for LP4. We read the web table and the Help Center article.
Can the LaserPecker 4 cut wood and acrylic?
With its 10W blue diode, yes: LaserPecker lists 8 mm balsa and 5 mm dark opaque acrylic in one pass. The 2W infrared marks only.
Is the LaserPecker 4 still sold?
Unclear. LaserPecker's store data showed every LP4 variant unavailable on 14 November 2026, though its pages and support site are live. Check before buying.