Home › Guides › xTool D1 Pro settings — cut & engrave cheat…
xTool D1 Pro laser settings — power, speed & passes
Starting-point power, speed and pass settings for the xTool D1 Pro, a 10 W 450 nm diode machine. These are collected figures, not results from running the machine ourselves. Every machine and material batch differs — treat these as a fast start, then confirm with a material test grid.
Quick answer: On the xTool D1 Pro (10 W diode), 3 mm plywood cuts at 100% power / 180 mm/min / 3–4 passes, MDF at 100% / 200 / 3 passes, and opaque acrylic at 100% / 120 / 4–5 passes. These xTool D1 Pro laser settings are starting points — confirm exact numbers with a test grid, and always run air assist for a clean edge.
Price a job on the xTool D1 Pro →xTool D1 Pro settings (power % / speed mm/min / passes)
| Material | Job | Setting |
|---|---|---|
| Plywood 3 mm | Cut | 100% / 180 / 3–4 passes |
| MDF 3 mm | Cut | 100% / 200 / 3 passes |
| Opaque acrylic 3 mm | Cut | 100% / 120 / 4–5 passes |
| Leather 2 mm | Cut | 90% / 250 / 1–2 passes |
| Cardboard | Cut | 80% / 500 / 1 pass |
| Wood | Engrave | 30% / 3000 mm/min |
| Slate / stone | Engrave | 80% / 2500 mm/min |
Clear acrylic: the xTool D1 Pro is a diode laser and cannot cut clear or transparent acrylic — the ~450 nm beam passes straight through. It can slowly cut dark, opaque acrylic only. For clear acrylic you need a CO2 laser.
Always: use air assist, focus for the exact thickness, and don't hold 100% power to force a cut — slow the speed or add a pass instead. Find your exact numbers with a material test grid.
All of these charts in one printable book: The Laser Settings Handbook — 18 machines, 11 material charts, the 15 fixes and a settings log in 168 pages. Read the free 13-page sample.
Get an exact price for the xTool D1 Pro
Settings give you the speed; the calculator turns your file's path length into machine time and cost, scaled to the xTool D1 Pro.
Open the xTool D1 Pro calculator →What a D1 Pro needs next to it
The D1 Pro is an open-frame diode: nothing stands between its 455 nm beam and your eyes, and air assist is a separate add-on. Those two gaps ruin more work, and carry more risk, than any setting on this page.
Safety glasses, 455 nm OD6+: Check price on Amazon ↗
Air assist pump: Check price on Amazon ↗
Honeycomb bed: Check price on Amazon ↗
Basswood sheets 3 mm: Check price on Amazon ↗
Still deciding? xTool D1 Pro: xTool store ↗ Check price on Amazon ↗
Sunglasses and generic tinted lenses are not protection at 455 nm. Buy glasses rated OD6+ at the diode's wavelength, and wear them every time the laser is on.
Disclosure: some links are affiliate links — if you buy through them we may earn a small commission at no extra cost to you. Prices are approximate list prices at the time of writing; always check the current offer.
Bed size: what actually fits
The xTool D1 Pro 10W has a working area of 430 × 390 mm (17 cm²). That decides which stock sizes you can buy without cutting them down first — the single most annoying thing to discover after the delivery arrives.
| Common stock | Size | On this machine |
|---|---|---|
| A4 sheet | 297 × 210 mm | Fits |
| 300 × 300 mm craft ply | 300 × 300 mm | Fits |
| 400 × 400 mm sheet | 400 × 400 mm | Does not fit — cut it down first |
| 600 × 400 mm sheet | 600 × 400 mm | Does not fit — cut it down first |
| 600 × 300 mm sheet | 600 × 300 mm | Does not fit — cut it down first |
Fitting parts onto the sheet efficiently is where material cost is actually won or lost. Our nesting tool takes your file and this bed size and tells you parts per sheet; the sheet yield calculator does the same from plain dimensions.
What the xTool D1 Pro 10W cannot do
Knowing the hard limits saves more material than any settings tweak:
- No clear or transparent acrylic. The ~450 nm beam passes straight through it. Dark, opaque acrylic cuts slowly; clear needs a CO2 laser.
- No glass or stone engraving without help. Glass is transparent to the beam — it needs a paint or tape coating to mark at all.
- No metal cutting. Marking anodised or coated metal works; cutting bare metal does not, at any power.
- Thick hardwood is slow. Multiple passes on anything past about 6 mm, and the edge quality drops with each one.
Troubleshooting: symptom, cause, fix
| Symptom | Usual cause | Fix |
|---|---|---|
| Cut does not go through, top looks fine | Focus set for the wrong thickness, or speed too high for the pass count | Re-focus for this exact sheet, then drop speed ~25% before adding a pass. Check the back face, not the top. |
| Edges heavily charred / flaming | No air assist, or too many slow passes stacking heat | Turn air assist on — it matters more than any setting tweak on wood. Prefer fewer, faster passes. |
| Clear acrylic does nothing at all | Physics, not settings | A diode cannot cut clear acrylic. Switch to opaque stock or a CO2 machine. |
| Engrave looks washed out / grey | Power too low, or lines per cm too high for the material | Raise power in 5% steps first. On wood, 50–80 LPC is usually enough — more just costs time. |
| Lines wavy or double-struck | Belt tension or the frame flexing at speed | Check belt tension and that the gantry is square. Reduce engrave speed to confirm it is mechanical. |
If none of that helps, work through why won't my laser cut all the way through? or how to stop burn marks on wood.
Material cost per sheet
Settings tell you the time; material tells you the rest of the price. Typical cut speeds and prices per sheet for the materials this machine handles: Plywood 3 Mm · Plywood 6 Mm · Mdf 3 Mm · Leather 2 Mm · Felt 3 Mm · Cardboard 3 Mm.
To turn any of it into a quote, drop your file into the xTool D1 Pro 10W calculator — it applies this machine's speeds to your actual path length. For shop pricing, the hourly rate calculator works out what your machine time is really worth.
FAQ
What power and speed cuts 3 mm plywood on the xTool D1 Pro?
On the xTool D1 Pro 10 W, a starting point for 3 mm plywood is 100% power at 180 mm/min, 3–4 passes. Values are starting points — run a small test on the same sheet, and use air assist for a clean edge.
Can the xTool D1 Pro cut clear acrylic?
No. The xTool D1 Pro is a diode laser (~450 nm); clear acrylic is transparent to it, so the beam passes straight through. It can cut dark, opaque acrylic slowly. Use a CO2 laser for clear acrylic.
How much does it cost to run the xTool D1 Pro?
Laser jobs are priced by machine time: cut length ÷ cutting speed × passes = time, then time × hourly rate + setup. Drop your file into the free calculator scaled to the xTool D1 Pro to get an exact time and price.
What is dot duration on an xTool laser?
Dot duration is how long the laser fires at each individual point when engraving in dot mode, measured in milliseconds — typically 0.1-1.0 ms. It is xTool's name for what other software calls dot time or dwell time. Longer dot duration burns each point deeper and darker but slows the job and widens each dot, so fine detail smears; shorter duration is faster and sharper but lighter. Start at 0.3 ms for wood and 0.5 ms for slate or anodised metal, then adjust in 0.1 ms steps. Dot duration only applies in dot or dithered engraving modes — in normal line (raster) engraving, speed and power control the burn.
What is lines per cm (LPC) in laser engraving?
Lines per cm sets how many engraving passes the head makes per centimetre of travel — the metric equivalent of DPI, and what controls resolution and how long the job takes. Typical values: 50-80 LPC for wood, 80-100 for acrylic and anodised metal, 100-130 for photo engraving. Doubling LPC roughly doubles engraving time, so raise it only until the lines just stop being visible — past that you are paying machine time for detail nobody can see. 100 LPC is about 254 DPI.
What are the xTool D1 Pro settings for MDF?
For 3 mm MDF, a starting point on the xTool D1 Pro is 100% power, 200 mm/min, 3 passes. Test on scrap first since MDF density varies by batch.
What are the xTool D1 Pro settings for leather?
Leather 2 mm cuts on the xTool D1 Pro at 90% power, 250 mm/min, 1–2 passes. Use air assist to keep the edge clean.