Home › Guides › xTool F1 vs F1 Ultra: what the 20 W fiber adds
xTool F1 vs F1 Ultra: what the 20 W fiber adds

Comparing the xTool F1 vs F1 Ultra? The F1 is a 10 W diode plus 2 W infrared head on a 115 × 115 mm bed. The F1 Ultra uses a 20 W diode plus a 20 W fiber laser on a 220 × 220 mm bed, which makes it a real metal-marking machine and a thin-metal cutter. The figures below are from xTool’s pages and our own two settings guides; we have not run either machine.
Quick answer: the F1 Ultra exists for metal: xTool lists it cutting 0.4 mm brass, 0.3 mm stainless and 0.2 mm aluminium, and its 20 W fiber marks bare steel at speeds of 1,600–2,200 mm/s in the library rows on our guide. The F1’s 2 W infrared marks metal too, at 550–600 mm/s on our F1 guide. For wood, leather and card the F1 Ultra’s 20 W diode is also stronger: xTool says 12 mm basswood against 8 mm.
xTool F1 vs F1 Ultra specs
| Spec | xTool F1 | xTool F1 Ultra | Source |
|---|---|---|---|
| Diode laser | 10 W, 455 nm | 20 W, 445 nm | xTool support articles 12, 1353 |
| Second laser | 2 W infrared, 1064 nm | 20 W fiber, 1064 nm | xTool support articles 12, 1353 |
| Work area | 115 × 115 mm (115 × 400 mm with slide extension) | 220 × 220 mm (220 × 500 mm with conveyor) | xTool support articles 12, 1353, tech-specs page |
| Max workpiece height | 113 mm | 145 mm | xTool support articles 12, 1476 |
| Max speed | 4,000 mm/s | 10,000 mm/s | xTool support articles 12, 1353 |
| Diode cuts | 8 mm basswood, 6 mm black acrylic (one article says 5 mm) | 12 mm basswood, 12 mm black acrylic | xTool support articles 1947, 12, 1476 |
| Metal cutting | None (marks only) | 0.4 mm brass, 0.3 mm stainless, 0.2 mm aluminium, repeated high-speed cuts | xTool support article 1476 |
| Camera | xTool’s F2 page says none; one F1 article mentions autofocus | “Smart Camera”, autofocus (no megapixel figure published) | xTool F1 Ultra product page, article 1476 |
| Software | XCS, LightBurn | xTool Studio, XCS, LightBurn | xTool support articles 12, 1476 |
| Offline storage | Not stated | 7 GB touchscreen controller | xTool support article 1476 |
| Weight | 4.6 kg | about 14.7 kg (retailer-reported, not from xTool) | xTool support article 12; retailer listing |
| Class | Not stated on the pages we read | Class 4 with the lid open | xTool support article 1476 |
What the settings say
Our F1 guide shows bare stainless engraved with the infrared at 50% / 550 mm/s / 200 lines per cm, one pass, and aluminium at 100% / 600 mm/s. Our F1 Ultra guide shows a 2 mm stainless pendant filled at 70% / 2200 mm/s and scored at 70% / 1600 mm/s with the fiber. These are different operations on different surfaces, so they are not a speed test, but the direction is consistent: the fiber runs several times faster. On dark acrylic 3 mm the F1 guide cuts at 100% / 2 mm/s in one pass; the F1 Ultra guide lists black frosted acrylic 3 mm at 100% / 25 mm/s over 5 passes, about 5 mm/s net: the stronger diode again goes faster. Most F1 Ultra rows come from xTool’s material library as published by a third party, and the rest from owners on Atomm; the guide marks which is which.
Which one should you get?
- Jewellery, dog tags, tumblers and bare metal in volume: F1 Ultra.
- Larger items, conveyor batches, thicker wood: F1 Ultra. The bed is 220 × 220 mm.
- Light engraving on a small bench, low weight: F1, if you can find one; see below.
Are they still sold?
On 14 November 2026 xTool’s US store listed the F1 Ultra as available in all its variants. It listed no new F1, only a refurbished one in limited quantities; xTool has not announced the F1 as discontinued. The F2 Ultra (60 W MOPA) now sits above the F1 Ultra: see F2 vs F2 Ultra. Sources are xTool’s own spec pages and support articles, listed in the table or at the end; xTool’s store pages and support articles do not always agree with each other, and where they do not, we say so.
FAQ
What is the difference between the xTool F1 and F1 Ultra?
Per xTool, the F1 has a 10 W diode and 2 W infrared laser on a 115 x 115 mm bed, and the F1 Ultra has a 20 W diode plus a 20 W fiber laser on a 220 x 220 mm bed. The F1 Ultra also cuts thin brass, stainless and aluminium; the F1 does not cut metal.
Can the xTool F1 Ultra cut metal?
Thin metal only. xTool's F1 Ultra Q&A lists 0.4 mm brass, 0.3 mm stainless steel and 0.2 mm aluminium with repeated high-speed cuts.
Is the xTool F1 Ultra faster than the F1?
xTool lists 10,000 mm/s maximum for the F1 Ultra and 4,000 mm/s for the F1. In our guides' metal marking rows the fiber runs at 1,600 to 2,200 mm/s against 550 to 600 mm/s for the F1's infrared; they are different operations, so it is not a like-for-like test.
How thick can the xTool F1 and F1 Ultra cut wood?
xTool says the F1 diode cuts up to 8 mm basswood and the F1 Ultra up to 12 mm, both in several passes. Those are ceilings, not recommended speeds.
Does the xTool F1 Ultra work with LightBurn?
Yes: xTool lists xTool Studio, XCS and LightBurn for the F1 Ultra, and XCS and LightBurn for the F1.
Is the xTool F1 Ultra still sold?
xTool's US store listed it as available on 14 November 2026. xTool's newer F2 Ultra (60 W MOPA) sits above it.
Where to look at them
xTool F1 Ultra: Check price on Amazon ↗
xTool F1: Check price on Amazon ↗
Disclosure: some links are affiliate links — if you buy through them we may earn a small commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Prices are approximate list prices at the time of writing; always check the current offer.